加拿大帕特森真空干燥機介紹-常州市至尊機械設備有限公司

加拿大帕特森真空干燥機介紹

發布日期：2021-8-17

帕特森Industries加拿大“過程裝備的人”的設計，工程和制造許多不同的工業和化學流程和應用程序的Conaform真空干燥機。帕特森Conaform干燥操作的原則基礎上，水或其它揮發性物質的高蒸氣壓的從一個區域移動到較低壓力區。這Conaform達到通過加熱干燥的材料，可以提高吸收的或游離液體的蒸氣壓，或通過真空或掃它帶走空氣流通過的蒸氣的氣體壓力降低。因此，很明顯，Conaform真空干燥系統中提供有效的干燥的基本條件，高效率和均勻的熱傳遞整個分批..和快速去除蒸汽。帕特森Conaform真空干燥機可以建在從1立方英尺（0.03立方米）的大小為371立方英尺（10.51立方米）的能力與體直徑從1'6“（0.46米），10英尺6英寸（3.2米）。帕特森Conaform干燥器是完全通過夾套循環熱水，油，蒸汽或蒸汽夾套和設計。由于Conaform單位轉動時，快速和連續的批次間混合帶來的每一個粒子在與被加熱的表面接觸。混合和折疊用的組合，可以實現均勻的溫度在整個批處理，因為沒有冷點，防止再縮合，并有助于快速的干燥速度和消除結塊。在理想的條件下，同時維持高真空的材料是在運動中，允許繪圖的水分。帕特森Conaform真空機是專為快速，高效的干燥各種各樣的化學品，藥品和食品。其獨特的雙錐形的回轉形狀，保證材料和加熱表面之間的直接接觸。這將導致在高效率和均勻的熱傳遞，并允許高速干燥，干燥溫度不提高被加工的材料的危險點。的PATTERSON Conaform是非常溫和的行動。移動部件的情況下，保證對解體的鋒利邊緣或拐角的晶體或磨損。由于是密封的烘干機，操作無粉塵。這意味著，沒有重大損失和沒有污染的氣氛。帕特森Conaform被設計為沒有電容器或其他輔助設備中使用的許多材料的干燥。，通常一個Conaform將取代整個系列的托盤微波爐。如冷凝器，傾析器等，是必需的，他們可以適當大小的為每Conaform的機。帕特森Conaform是提供一個特殊的分散機制稱為作為Conagrator，材料傾向于在干燥過程中形成硬塊。使用一個Conagrator有助于實現高的干燥速率，即使當處理結晶材料。應用范圍：帕特森Conaform真空干燥機在除了干燥功能，也可以用于混合，加熱，冷卻和用于液體或氣體的添加劑等功能。它們被用于廣泛的食品物質，藥品和化學品干燥。帕特森Conaform真空機已經使用的進程，需要預混合的液體添加劑，此外，加熱的內容帶出了反應，清除多余的水分，^后冷卻批次的產品。設計特點：室內清潔 - 易于保持清潔 Conaform干燥器的內部僅由光滑的側壁，通過它的熱量被傳遞到產品。干燥室的獨特的雙圓錐形狀實現混合和摻合的行動。缸和截錐體的相交是鈍角，所以沒有材料被困住。有沒有內部的刮削器，犁，勺子或葉片捕獲和材料，或防止干燥均勻。Conaform可以很容易地清洗快速變化的產品或顏色，保持^小的過程。此功能使一個干燥器沒有交叉污染的產品可用于許多不同的試劑級化學品的^高純度。致密真空密封 Conaform有一個填料函，在入口處的蒸汽管道。易于維護，高效真空，真空能力過剩并不需要提供的泄漏。其他固定筒干燥機的類型與水平軸攪拌器需要兩個填料箱，或批次的軸承內部。軸承OUT的批處理所有軸承的Conaform安裝在干燥室的外面。有沒有潤滑劑的產品污染的可能性。真空密封無塵排氣閥為了保持^高的產品純度和無塵操作，Conaform干燥器配有特別設計的真空密封的排出閥。該閥是一個光滑的板坐在與蝸桿驅動器。有一點力氣堅決座閥。通暢的流動，類似一個閘閥，它完全打開，但沒有任何凹槽或通道捕獲材料。圍繞閥的輪輞提供的座椅的安裝套筒，所以也沒有損失的產品和沒有在放電過程中的污染。無破損或磨損的晶體 Conaform機是溫和的行動。整個沒有移動部分內的Conaform確保打擊解體的鋒利邊緣或拐角的晶體或磨損。這是一個無灰塵的^終產物所需的特殊的優勢。無結塊 - NO污染由于Conaform旋轉，和真空吸走水分，顆粒不斷地改變自己的立場。沒有結塊，或污染的Conaform，在其他類型的干燥器。晶體板或拉長身材不包，但采取隨機的方向，開放空間的蒸氣逃脫。溶劑回收帕特森Conaform干燥器干燥價值高的材料是特別有用的。從在干燥的材料中提取的溶劑或液體可以回收所使用的冷凝器。輔助設備，如冷凝器，傾析器，等等，可以提供與任何規模的Conaform干燥器。可以使用不帶冷凝器 Conaform可以用于多種材料的干燥沒有電容器或其他設備。優于盤架干燥 conaform真空干燥是優異的許多方法來托盤干燥。在盤架干燥，循環空氣預熱的材料和刪除只從表面層中的水分。所有的蒸汽沒有上升到表面，但移動到的地方的^低蒸氣壓力 - 通常是中心的批次，由于惡劣的熱滲透。這里，它被冷凝，或者被重吸收引起結塊。通過熱傳導的材料的多孔床總是慢，和輻射轉移是眾所周知的低效率的，在低溫下，與真空干燥。同時在真空條件下干燥Conaform原則消除這些不足之處，并提供一致的產品每次。單位可以單獨設計，以客戶的材料規格和工藝參數。完成的Conaform的規格表，并通過電子郵件或傳真提交帕特森的報價。完成PATTERSON真空干燥系統由以下幾部分組成：（A）PATTERSON＃5 1'0“體直徑Conaform真空式干燥機 - 雙圓錐機，^大工作容積0.32立方英尺，額定工作容量：0.32立方英尺，身體總體積：0.49立方英尺，約。換熱面積：2.9平方尺接觸的所有部件：316不銹鋼，夾克產品支持的立場和基地304不銹鋼。設計條件：吹風機本體：100（212），全真空外套：25 psig至100（212）一致內部全真空，內表面拋光，電拋光180號，體絕緣，SS304護套覆蓋，完整的HP不可分割的體速度：10 rpm的電機減速機，齒輪。應用領域：癌癥藥物的研究/制造（B）1.25 HP TEFC電機與單級旋片式真空泵真空系統，泄壓閥，進口止回閥。（C）（1）只有4.5千瓦熱水/冷卻循環水系統與電子溫度和過程控制器，具有數字通信接口，主控制面板。（D）控制系統的面板。自動基于微型處理器的控制系統將保持設定溫度的加熱周期的長度上。在加熱周期的時間和其他參數將被設置在開始的過程周期。溫度和真空度，將被記錄的周期的長度上，并可以被下載到一個標準的PC擴散片材或其他格式。該系統會自動將控制的序列過程循環，烘干機旋轉，熱真空，熱切斷周期結束時。該控制系統包括：主輸入開關斷開安裝在面板上的人機界面觸摸屏PLC 8“標準彩色面板，640×480像素的分辨率與相應的圖形顯示控制所有設備，如烘干機，真空系統和加熱器。數字溫度指示器真空泵控制數字真空指示器機控制電阻式模擬觸摸屏作為人機界面 RS232通訊端口和RS485連接到PC的數據采集等（E）系統的所有組件連接到控制面板間的連接管道是撬裝驅動系統側視圖非系統驅動器的側視圖熱水/冷卻循環水系統控制面板的前視圖關閉真空泵主屏幕機控制過程控制真空控制設定點的溫度增量小時容器的溫度溫度監控器溫度監控器調節對比度報警歷史記錄控制系統 請注意：帕特森的內部專業知識，設計和提供我們所有的工藝設備的操作控制系統，無論是一個簡單的開始/停止周期時間或執行復雜的多階段系統配方或公式，并與現有的工廠控制系統。關閉控制箱，起動/停止，點動/運行和0-12小時定時器。包括HMI觸摸屏控制面板概述。特寫與PLC和變頻電機控制器的控制面板內的。PATTERSON Industries Canada "The Process Equipment People" designs, engineers and manufactures Conaform Vacuum Dryers for many different industrial and chemical processes and applications. The PATTERSON Conaform drying operations are based on the principle that water or other volatile material moves from a zone of high vapor pressure to a zone of lower pressure. The Conaform attains this by warming the material to be dried to raise the vapor pressure of the absorbed or free liquid, or by decreasing the vapor pressure of the gas by vacuum or by sweeping it away with an air current. Thus, it is apparent that the Conaform Vacuum Dryer System provides the essential conditions for effective drying, efficient and uniform heat transfer throughout the batch .. and rapid removal of vapor.PATTERSON Conaform Vacuum Dryers can be built in sizes from 1 cubic foot (0.03 cu. m) to 371 cubic feet (10.51 cu. m) capacity with body diameters from 1' 6" (.46 m) to 10' 6" (3.2 m).PATTERSON Conaform Dryers are completely jacketed and designed for circulating hot water, oil, steam or vapors through the jacket. As the Conaform Unit rotates, the rapid and continuous inter-mixing of the batch brings every particle in contact with the heated surface. The combination of blending and interfolding helps achieve uniform temperature throughout the batch, prevents re-condensation since there are no cold spots, and contributes to rapid drying speed and the elimination of caking. Maintaining a high vacuum while the material is in motion permits the drawing off of moisture under ideal conditions.The PATTERSON Conaform Vacuum Dryer is designed for fast, efficient drying of a wide variety of chemicals, pharmaceuticals and food products. Its unique double cone rotating shape assures direct contact between the material and the heated surfaces. This results in efficient and uniform heat transfer and permits high speed drying without raising the drying temperature to the danger point of the material being processed.The PATTERSON Conaform is exceptionally gentle in action. The absence of moving parts assures against disintegration of crystals or abrasion of sharp edges or corners. Since the dryer is hermetically sealed, operations are dust -free. This means no material loss and no contamination of the atmosphere.The PATTERSON Conaform is designed for use in the drying of many materials without condensers or other auxiliary equipment. One Conaform will usually replace an entire series of tray ovens. Where condensers, decanters, etc., are required, they can be properly sized for every Conaform Dryer.The PATTERSON Conaform is available with a special dispersing mechanism known as the Conagrator, for materials that tend to form lumps in the drying process. The use of a Conagrator helps achieve high drying rates even when handling crystalline material.Applications:The PATTERSON Conaform Vacuum Dryer in addition to the drying feature can also be used for such functions as blending, heating, cooling and for liquid or gaseous additives. They are used for drying a wide range of food substances, pharmaceuticals and chemicals.The PATTERSON Conaform Vacuum Dryer has uses in processes requiring pre-blending, addition of liquid additives, heating the contents to bring out a reaction, removal of excess moisture and finally cooling of the batch of product.Design Features:A CLEAN INTERIOR - EASY TO KEEP CLEAN The interior of the Conaform Dryer consists only of the smooth sidewalls, through which the heat is transferred to the product. The unique double-cone shape of the drying compartment achieves the mixing and blending action. Intersections of cylinder and truncated cones are obtuse angles, so no material is trapped. There are no internal scrapers, plows, scoops or vanes to trap and hold material or prevent uniform drying.The Conaform can be easily cleaned for quick change of products or colors, with minimum process hold-up. This feature enables one Dryer to be used for many different reagent-grade chemicals of highest purity without cross contamination of products.TIGHT VACUUM SEAL The Conaform has one stuffing box-at the entrance of the vapor pipe. A highly efficient vacuum is easily maintained, as excess vacuum capacity is not required to provide for leakage. Other dryers of the stationary cylinder type with horizontal shaft agitator require two stuffing boxes, or a bearing inside of the batch.BEARINGS OUT OF THE BATCH All bearings of the Conaform are installed outside of the drying compartment. There is no possibility of product contamination from lubricants.VACUUM-TIGHT DUSTLESS DISCHARGE VALVE To maintain highest product purity and dust-free operation, the Conaform Dryer is fitted with a specially designed vacuum-tight discharge valve. The valve is a smooth plate seated with a worm drive. There is little effort required to firmly seat the valve. It opens fully, for unobstructed flow, similar to a gate valve, but has no grooves or channels to trap material. The rim around the valve provides a seat for attaching a sleeve, so there is no loss of product and no contamination during discharge.NO BREAKAGE OR ABRASION OF CRYSTALS The Conaform Dryer is gentle in action. The entire absence of moving parts within the Conaform ensures against disintegration of crystals or abrasion of sharp edges or corners. This is of special advantage where a dust-free final product is desired.NO CAKING - NO CONTAMINATION As the Conaform rotates, and the vacuum draws off moisture, the particles constantly change their position. There is no caking, or contamination in the Conaform, as in dryers of other types. Crystals of plate or elongated shape do not pack but take random orientation, leaving open space for vapor to escape.FOR SOLVENT RECOVERY The PATTERSON Conaform Dryer is particularly useful for drying materials of high value. Solvents or liquids extracted from the materials being dried may be recovered by the use of condensers. Auxiliary equipment, such as condensers, decanters, etc., can be supplied with any size Conaform Dryer.MAY BE USED WITHOUT CONDENSER The Conaform can be used for drying many materials without condensers or other equipment.SUPERIOR TO TRAY DRYING Conaform vacuum drying is superior in many ways to tray drying. In tray drying, the circulating air warms the material and removes moisture from the surface layer only. All vapors do not rise to the surface but move to the place of lowest vapor pressure - often the center of the batch, because of poor heat penetration. Here it is condensed or is reabsorbed to cause caking. Heat conduction through a porous bed of material is always slow, and transfer by radiation is notoriously inefficient at the low temperature associated with vacuum drying. The Conaform? principle of simultaneous drying under a vacuum eliminates these deficiencies and delivers a consistent product everytime.Units can be individually designed to customer's material specifications and process parameters. Complete the Conaform Specification Sheet and submit by e-mail or fax to PATTERSON for quotation. Complete PATTERSON Vacuum Drying System consisting of the following components:(A) PATTERSON Model #5, 1'0" body diameter Conaform Vacuum Dryer-Double Cone Dryer, Maximum Operating Capacity 0.32 cu.ft, Nominal Working Capacity: .32 cu.ft, Total Body Volume: 0.49 cu.ft, Approx. Heat Transfer Area: 2.9 sq. ft. All parts contacting product 316 stainless, Jacket support stands and base 304 Stainless Steel. Design Conditions: Dryer Body: Full Vacuum to 100 (212), Jacket: 25 psig to 100 (212) coincident with Internal Full Vacuum, Internal surfaces polished to 180 grit followed by electro-polishing, body insulated and covered with SS304 sheathing, complete with HP integral gear motor reducer, Body Speed: 10 rpms.Application: Cancer Drug Research/Manufacturing(B) Vacuum System with single stage Rotary Vane Vacuum Pump with 1.25 HP TEFC motor, bleed valve and inlet check valve.(C) One (1) only 4.5 kW Hot Water/Cooling Circulating System with electronic temperature and process controller with digital communication interface to main control panel.(D) Control System with Panel. The automatic micro processor based control system will maintain the set temperature over the length of the heating cycle. The time for the heating cycle and other parameters will be set at the beginning of the process cycle. Temperature and vacuum will be recorded over the length of the cycle and can be downloaded to a standard PC spread sheet or other format. The system will automatically control the sequence for process cycle, Dryer rotation, heat, vacuum, cut off of heat at end of cycle.The Control System includes:Main input disconnect switch Panel-mounted HMI Touch screen PLC 8" Standard colour panel, 640 x 480 pixel resolution with appropriate graphics showing control of all devices such as Dryer, Vacuum System, and Heater. Digital Temperature Indicator Vacuum Pump Controls Digital Vacuum Indicator Dryer Controls Resistive Analog Touchscreen as HMI interface RS232 communications Port and RS485 for connection to PC for data acquisition etc. included (E) System is skid mounted with all components wired to the control panel and inter-connecting piping Drive side view of System Non Drive Side view of System Front view of Control Panel with Hot Water/Cooling Circulating System Close up view of Vacuum Pump Main Screen Dryer Control Process Control Vacuum Control Set point Temperature Increment Hour Vessel Temperature Temperature Monitor Temperature Monitor Adjust Contrast Alarm History Control Systems Please note: PATTERSON has in-house expertise to design and supply operating control systems for all of our process equipment, whether it is a simple start/stop with cycle time or complex multi-stage systems executing recipes or formulas and communicating with existing plant control systems.Close up of Control Box with stop/start, jog/run and 0-12 hr timer. Control Panel Overview including HMI Touch Screen. Close-up of Inside of Control Panel with PLC and Variable Frequency Motor Controllers.

隨著節能環保，且能保證物料本身性質的真空干燥機出世以來，一直在市場上居高不下，使用的企業單位越來越多。作為專業的真空干燥機生產廠家提醒您，一定要關注真空干燥機操作注意事項及保養，這樣才能使真空干燥機^大限度的發揮其真正的價值，也可以節約您的經濟成本。就真空干燥機操作注意事項及保養給您提以下幾點意見。與傳統的快速干燥機相比，催化劑真空干燥機是非常適合于從漿液制造用催化劑的載體，它具有主要優勢是能源效率更高。混合器和真空干燥器非常適合浸漬帶有活性基團的催化劑載體，它們提供了溫和的混合和干燥過程，這是必需的，因為催化劑的相對大小可以決定活性和選擇性。通隨著真空干燥機的發展，其子產品有不斷推出，雙錐回轉真空干燥機是其中比較受歡迎的。雙錐回轉真空干燥機是現如今在物料上適用比較廣泛的一種干燥設備。相信大家對雙錐回轉真空干燥機會有很多疑問，小編在此主要先給大家分析一下其優勢及如何選擇？雙錐回轉真空干燥機優勢有很多。第一是其真空環節能夠輕松高效的干燥物料，烘干機的加熱或冷卻應緩慢進行，用戶應根據情況采取適當?shù)纳仙拖陆邓俣龋辉谡婵崭稍餀C的運行期間，有必要按照標準程序進行采樣，然后采樣完成并重新開始。滾動軸承選用MOS2復合潤滑脂（ZFG-IE）的溫度可達150度，每月至少一次，發現潤滑脂干后，應及時更換人們對食品保存的要求越來越高，已經不僅僅滿足只是脫水蔬果的簡單要求，更要求食品能保持原有的營養，色香味型，故食品干燥一直是研究者持之不懈的課題。干燥專業研究食品干燥十幾年，通過不斷地努力研究，已經與國外技術的相結合，在真空干燥機的基礎上推出一款真空冷凍干燥機。真空冷凍干燥機為食品的干燥保存技術更添一